1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp
1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp

1/10 Scale Full-Width Front Bumper For Axial SCX10 III Base Camp

$53.95 USD
-1 in stock
Axial Full-Width Steel, Welded Front Bumper for the Axial SCX10 III Base Camp.

Full width and full scale! This Class 1 worthy low-profile front bumper allows for full tire clearance under full turn & compressionIt even includes the ability to mount a winch behind the grill. 
(MADE FOR STOCK VEHICLE- Any modifications may affect clearance) 


Specifications:
-195mm wide, raised approx. 20mm above top of frame rails to close body gap.
- Predrilled with mounting holes to fit the RC4WD 9.5 CTI hole pattern. *Bumper is made to allow for a bumper-mounted winch behind the grill/body, not in front.
- Mounts using included hardware. Spacer/additional washers may be necessary.
- Steel construction - Hand Made/Welded.
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel.

 **Please Note: Our finish options provide a superficial coating and will scratch/chip under normal use. Pros/cons of each can be found below:

-Raw Steel: We recommend a raw steel finish if you want the scale patina of the bare metal, which will rust over time, or if you intend to coat with a harder finish on your own,

-Flat Black: not as susceptible to chips

Mounting Instructions:

1. Bumper is made to slide inside the c-channel of the frame rails. 

2. Back screws with a washer and nut.

 

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

You may also like

Quick View
Heavy-Duty Land Anchor w/ Hook Add-On
$20.00 USD
Quick View
Heavy-Duty Hybrid Land Anchor Add-On
$27.00 USD
Quick View
Heavy-Duty Land Anchor Add-On
$18.50 USD
Quick View
Rear Bumper for Axial SCX10 III Jeep CJ-7
from $54.95 USD
Quick View
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
from $62.95 USD

Heavy-Duty Land Anchor w/ Hook Add-On

$20.00 USD

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Heavy-Duty Hybrid Land Anchor Add-On

$27.00 USD

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Heavy-Duty Land Anchor Add-On

$18.50 USD

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Rear Bumper for Axial SCX10 III Jeep CJ-7

$54.95 USD

ScalerFab Rear Bumper for Axial SCX10III Jeep CJ-7

Experience the ultimate in scale appearance with our Rear Bumper for the Axial Jeep CJ-7. Made from strong metal, this bumper not only looks like the real thing, but also offers added durability and protection for your RC vehicle. Customize your bumper even further with optional add ons like the tire carrier. Upgrade your RC experience today!

The ScalerFab SCX10 III bumpers are designed to work with the stock Axial CJ-7 body post mounting system. Rear bumper includes body posts that fit into the mount on the body.

Specifications:

- Approx. 190mm wide
-Mounts using existing holes in frame rails. Washer and nut recommended- see mounting instructions below.
- Steel construction - Hand Made/Welded.

Mounting Instructions:
-Bumpers mounts to outside of frame rails, between the plastic fenders and the frame rails.

**For extra tight fit, use a dab of Shoe Goo or E6000 Clear Adhesive between the frame rail and the bracket, and screwing down tight with a nut, and let sit overnight. 

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7
Rear Bumper for Axial SCX10 III Jeep CJ-7

Customer Reviews

Based on 2 reviews
50%
(1)
0%
(0)
50%
(1)
0%
(0)
0%
(0)
J
JR
Solid steel. Great people to work with!

With some very minor adjustments the bumper fit perfectly. If I need more parts I’ll contact these guys!

J
Jeffrey

Didn’t get what I ordered. I ordered a bumper with a stinger on it.

Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7

$62.95 USD

ScalerFab Welded Steel Replica Winch Front Bumper for Axial SCX10III Jeep CJ-7 

Trail Bar & Stinger options available.

*This bumper is made to fit a bumper-mounted winch. Click for Non-Winch Bumper For CJ-7. 

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle while still allowing for a bumper-mounted winch. 

The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.

Specifications:

- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Includes Pre-drilled mounting holes for winch (RC4WD WARN 9.5cti and 8274 Winch, 3Racing Winch, and SSD Ox Power Winch mounting pattern)
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment

TO MOUNT WINCH: You will need to flip the winch mounting plate in order to install on bumper.
   
Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails. 
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.

3. Back screws with a washer and nut.

ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10III Jeep CJ-7 Trail Bar & Stinger options available.

*This bumper does NOT fit a winch. Click for Winch Bumper For CJ-7. 

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.

 

The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.

Specifications:

- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment

Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails. 
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.

3. Back screws with a washer and nut.

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7

Customer Reviews

Based on 3 reviews
67%
(2)
0%
(0)
0%
(0)
0%
(0)
33%
(1)
H
Hans Günther Ludwig

Metal Replica Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7

J
Jason Sponberg
SCX10iii Jeep CJ-7 winch bumper

Product looks great!!
Had to do some fabrication to bumper to make it fit
It must not have been test fitted after welding was done
I had to grind down left side where it fits inside the frame, bumper would not slide in far enough to insert bolts, it was hitting the bend in the frame.
I also had to drill out washers used to attach body, holes were not large enough to allow body posts to slide into place to secure body
I hope this information helps out, to prevent future issues.
I’m a huge fan of scalerfab and I have had nothing but great success with your products
Keep up the amazing work
Thanks

S
Skip Nicholson
CJ7 front bumper

Great job. But I think you should put the D ring mounts on the front of your bumper, they hang too low 👍🏻

Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7

$57.95 USD

ScalerFab Welded Steel Replica Non-Winch Front Bumper for Axial SCX10III Jeep CJ-7 Trail Bar & Stinger options available.

*This bumper does NOT fit a winch. Click for Winch Bumper For CJ-7. 

Expertly crafted metal front bumper designed specifically for Axial Adventure's SCX10 III Jeep CJ-7. Made with durable metal for a realistic scale appearance and unbeatable performance. Provides the lowest approach angle without sacrificing strength. Don't worry about running a winch - this bumper is designed for maximum performance.

 

The ScalerFab SCX10 III CJ-7 bumpers are designed to work with the stock CJ-7 body post mounting system and includes post mounts build into the bumper. Bumpers will not mount with any after-market crossmembers or anything that would interfere with the end of the frame rails.

Specifications:

- 80mm wide
- Requires removal of stock bumper mount/plate. Bumper fits into the ends of the C-Channel and mounts using existing holes in frame.
- Steel construction - Hand Made/Welded.
- No fore/aft adjustment

Mounting Instructions:
1. Bumper is made to slide inside the c-channel of the frame rails. 
2. Mount by matching holes in the body post mount with holes in the brackets and frame rails, as shown below.

3. Back screws with a washer and nut.

Lifetime Warranty Info

ScalerFab Offers a Lifetime Warranty on all of our Trail Armor. We warranty against breakage and bending of non-modified Bumpers, Rock Sliders, Roof Racks, Hitches, etc. 

 If you have an issue with your item, please leave detailed info below or you can mail in with info.

Items for warranty repair/replacement can should be mailed to:

ScalerFab, Inc
PO Box 130
Divide, CO 80814

Replacement and/or refunds typically processed within 5-7 business days upon receipt of item. (Management reserves all rights)

Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7
Metal Replica Non-Winch Front Bumper for Axial Adventure SCX10 III Jeep CJ-7

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
Back to Eligible for Gift Cert Redemption